Rear cross member waxing
Service Actions:. Depends on the condition of your chassis, but I'd say it has to be fairly rusty to actually make it stick. Recommended Posts. Log in. Forums New posts. I have not managed to talk to MOT guy yet and presumably an advisory means its not likely to fail just yet and I do not tow with it. Thanks in advance. Media New media New comments. Media New media New comments.
In the next few weeks i will be protecting my rear crossmember from i will also be injecting wax into the crossmember internally, i like Bilt. They informed me of this recall and carried out what was termed "rear cross member waxing" which is, I gathered, rustproofing.
In my area road.
Any ideas what is the best paint to use on the rear cross member to. I certainly like the idea of using underbody wax - but does/will this not.
I am sure Tony White90 will have some comments on POR15, however after using on the chassis of theI would have to say that I can't confirm the marketing blurb.
I was researching what wax to use and turned up some interesting stuff being sold by a company called rust buster While you're in waxing mode, put on the long probe and wiggle it up through the drain holes in the bulkhead legs, above the two big bolts, until you can hear the end scratching around right up in the top corner of the BH, then squeeze the trigger and let it gush out while slowly withdrawing the probe.
Impact resistance: DIN 55 Granville metal finish paint once cured shows excellent impact resistance.
Resources Latest reviews. Note: Your post will require moderator approval before it will be visible.
TANG RESTAURANT 75016 ZIP CODE
|Brush: Using a suitable sized brush apply paint evenly using multi-directional strokes.
Finger and thumb are moving Log in Register. While you're in waxing mode, put on the long probe and wiggle it up through the drain holes in the bulkhead legs, above the two big bolts, until you can hear the end scratching around right up in the top corner of the BH, then squeeze the trigger and let it gush out while slowly withdrawing the probe. On ferrous substrates it provides a tough impermeable barrier to air and moisture which effectively seals out corrosion.
If you would like to register then please Click Here.
but spray the inside liberally with a corrosion wax (Dinitrol or other.
Kia Rondo Recalls kiarondo
› kia-rondo › kia-rondo-recalls. Kia Rondo.
Service Campaigns: SCRondo (UN) Rear Cross Member Waxing. SCApplication of Additional Anti-Corrosion Material. Service Actions.
Thanks for all the useful replies Clive's location not that far away from me.
Video: Rear cross member waxing WAXING MY ENTIRE BODY *yes everything*
Messages 10, Points Share this post Link to post Share on other sites. Posted August 22, SASome Rondo UN vehicles may experience a noise originating from the upper end of the front strut while driving on.
Discovery II > Land Rover Workshop Manuals > CORROSION PREVENTION AND SEALING > CORROSION PREVENTION > Cavity wax treatment areas and.
Chassis cleaning advice. Land Rover UK Forums
I reckon you can get a rear cross member for easy less than £, I'm inside waxed, loom pulled through and connected back up, to bar re.
If you would like to register then please Click Here. Use a gun pressure of psi.
Video: Rear cross member waxing Best Unwanted Hair Removal -Full Face Waxing - Curly Hair Straightening Tutorial - Episode 17
It is also recommended to wash the surface with detergent and water to remove oil and grease. Chassis cleaning advice. Posted August 22, SAIn Some MY Kia Rondo vehicles there is a possibility that the clock spring contact assembly may become worn over time and need replacing. I put POR15 on my chassis and it's stuck brilliantly to the slightly rusty rear section of chassis, but peeled off in sheets on any vaguely smooth metal or with a coat of paint over it fuel tank etc.
Rear Crossmember Rust Prevention Defender Forum LR4x4 The Land Rover Forum
FEIRA DE SAUDE 2015 FORM
|Unlike currently available metal finishes, it does not contain harmful solvents and has been designed to be slower drying making it easier and safer to use.
Posted August 18, Anybody see any flaws in that or have any tips, like i say i want to get it right. That would be at lest half probably more than the vehicles current worth, so is that cost about right? You will need a nice warm day and mix with white spirit, I did not drill any extra holes, but I squirted the wax into every hole I could find.